Product news
Evolis Primacy Card Printer Regular Cleaning
Evolis Primacy Card Printer Periodic cleaning method through machine panel operation.
The Primacy machine is operated through the machine panel for regular cleaning. Please follow the steps below for regular cleaning:
Repeated runs through the printer with the cleaning card clean the cleaning roller, maintaining print quality and extending the life of the printhead.
How to Clean the Evolis Primacy Printer. Insert the cleaning card in the opened feeder, adhesive face upwards. This starts the cleaning. Adhesive card.
1. Open the printer cover.
2. Take out the ribbon.
3. Close the cover and make sure to hear a click.
4. Open the card feeder on the printer.
5. Use the ruler to adjust the card thickness to the maximum position.
6. Take out all the cards in the card feeder.
7. Double-click the cleaning button on the control panel, and then insert the cleaning card .
8. Peel off the film on the cleaning card, insert the cleaning card into the card feeder according to the picture, with the sticky side facing up.
9. The used cleaning card will automatically pop into the output tray. Regular cleaning is done.
Card Printer Cleaning Roller
Card Printer Cleaning Roller
The card printer cleaning wheel is a product specially designed to clean the card when producing the card. Put the cleaning wheel into your printer, the cleaning wheel will absorb the dust particles on the card during printing, which will prolong the life of your print head and improve the quality of your card punching.
It is highly recommended to perform a printer cleaning every time the ribbon is replaced. In addition to using the cleaning card to clean the card channel, each cleaning also includes replacing the card cleaning roller.
Watch out for a lot of dust particles on your cleaning wheel, or clean it after every 250 cards printed.
Note your printer model, it may have one or two cleaning rollers.
Instructions:
1. Open the top cover of the machine.
2. Remove the ribbon and printer cleaning roller from the printer.
3. Locate and remove the cleaning roller between the two ribbon drive rollers.
4. Peel off a layer of thin paper on the cleaning card, attach the cleaning card to the cleaning wheel and drag the cleaning card overturned to make it absorb the dirt and dust on the cleaning wheel to the cleaning card.
HiTi CS-220E Card Printer Ribbon not Detected
HiTi developed the CS-220E card printer and reported that the ribbon was not detected when it was powered on
HiTi card printer CS-220E reports 0201 No ribbon detected when the machine is turned on.
If this error occurs, the machine failure can be eliminated from the following points.
1. Check whether the ribbon is installed in the machine, if not, please install the ribbon correctly.
2. Whether the ribbon in the machine is installed correctly, if the ribbon is installed incorrectly, please install the ribbon correctly.
3. The ribbon in the machine is broken, connect the broken part, stick it with tape, and reinstall the ribbon correctly.
4. You can calibrate the sensor for the machine in the printing preferences.
If the machine still reports an error after eliminating the above points, please contact our technical department in time!
Yousite company offers many OEM cleaning card solutions to suit your needs, including private label cleaning card.We are producing card printer cleaning kits and supplying all major brands Manufacturer of a full range of cleaning supplies. We can customize and produce standard size IPA according to customer’s requirements Soak cleaning card, sticky rollers, sticky card, IPA cleaning pen and IPA cleaning cloth
Label, Receipt and Barcode Printer Cleaning Card/Kits
Cleaning Cards/Kits | Label, receipt and barcode printer cleaning card
Whether you utilize paper, linerless labels, or linered label rolls in your printer, a routine cleansing timetable is the very best means to make certain optimal printer performance and print high quality.
Yousite cleansing products will certainly: Eliminate glue residue, dust as well as various other contaminates that can create label jams and cause printer element damage Prolong the life of the thermal printhead and also rollers Keep your published picture looking clean and crisp Cleans printhead, paper guides and paper path
Select from our:
Remove dust, debris and oils that build up over time during the normal operation of your remote deposit check scanner. Check Scanner Cleaning Kit
Expert Cleaning Package Cleaning Cards
Regular cleaning with Yousite Materials can substantially prolong printhead life. View the return on your investment expand with these user friendly regular maintenance items.
Common Faults And Solutions of ZEBRA Barcode Printers
Common faults and solutions of ZEBRA barcode printers
When we use Zebra printers, we will inevitably encounter some operational problems or printer failures because we are not familiar with the printer or have used the printer for a long time. Now Xiaobian has sorted out various common Zebra printer faults and solutions for you
Fault 1: The printing software cannot print Chinese characters
Analysis: Many printing software use the Windows print driver to print Chinese characters through the printing software, so you need to choose a suitable printing program to print Chinese characters.
Solution: Use a good driver, such as Seagull driver, or use BarOne software to directly drive the printer.
Fault 2: Replace the label paper, and the carbon ribbon appears after printing
Analysis: The label printer recognizes the label paper, and the ribbon sensor has a memory function. When replacing the label paper and ribbon, it cannot be recognized.
Solution: The paper needs to be remeasured. Use the Zebra label printer S such as 400, under normal startup, press the MODE button three times and then press the FEED button. At this time, a lot of paper will come out. When the paper comes out, it will be the measurement paper, and the information will be automatically recorded on the sensor of the printer. Need to measure the paper again, it can be used normally.
Fault 3: When printing a large label, only half of it is printed
Analysis: This is because the memory of the label printer is too small. When the label is too large, some information cannot be stored and lost.
Solution: Increase the memory of the label printer.
Common Faults and Solutions of Zebra Printers
Fault four: unclear printing, poor quality
Analysis: There are three possibilities, first, the print head may not be installed correctly; second, the temperature is too low; third, the quality of the label paper and ribbon is poor.
Solution: For one, readjust the position of the print head, paying special attention to the consistency of left and right height; for the second, increase the printing temperature, that is, increase the printing density; for the third, replace better label paper and ribbon.
Fault five: Ribbon wrinkled
Analysis: It may be that the temperature setting of the label printer is not correct, it may be that the ribbon around the machine is not correct, or the media is not set correctly for the amount of paper, it may be that the pressure and balance of the print head are not set correctly
Solution: reinstall the driver, adjust the printing temperature, and adjust the printing pressure.
Fault 6: The vertical direction is missing during the printing process of the barcode printer
Analysis: This may be caused by long-term use of the printer or dust coverage on the surface of the print head
Solution: Clean the print head with alcohol swab first , if it is still abnormal, contact the dealer to replace the print head.
Fault 7: All the indicators of the label printer are flashing, and the paper cannot be measured
Analysis: If this happens, it means that the sensor cannot be recognized or is broken.
Solution: Clean the sensor first to remove the dust on the surface. If it cannot return to normal, you need to contact the dealer to replace the sensor.
Fault 8: LCD does not display and cannot be operated
Analysis: In this case, the motherboard or EPROM is damaged
ZEBRA ZC100 Card Printer Cleaning Card
ZEBRA ZC100 card printer cleaning card
Selling card printers for nearly 10 years, and has accumulated rich after-sales experience and customer feedback cases.
According to our after-sales statistics, users report that 80% of card printing problems can be solved with cleaning cards.
Used for a long time, there may be some residues and dust in daily life inside the machine.
The card feeding channel is a very important part of all the components of the ZC100 card printer, which will directly affect the printing quality.
ZEBRA (Zebra) ZC100 card printing belongs to the equipment category, regular cleaning can keep the printer in a better condition and prolong the life of the printer.
Zebra cleaning card is a special cleaning card for ZC100 card printing. It is a cleaning product composed of ultra-pure solvents, additives and composite materials with strong adsorption capacity.
It can Quickly and safely remove dust, oil and other contaminants from the ZC100 card printer.
Integrity shapes the brand, quality opens up the market. Our company has been committed to providing users with high-quality products and satisfactory services. Yousite specializes in the production of printer consumables . If you have more questions about ZC100 card printer cleaning cards, please contact us.
For the steps of using the cleaning card of ZEBRA ZC100 card printer, please pay attention to our company for more technical news.
Zebra Barcode Printer Cannot Print
Zebra Barcode Printer Cannot Print
When we use Zebra in the barcode printer, there is often no response failure after pressing the print button, so how should we deal with this situation?
Many friends who are not familiar with printers may think that the printer is broken, but this is not the case. The following examples are the common faults that Zebra barcode printers cannot print. Take this as an example and hope it will be helpful to everyone.
1. One of the most common failures of Zebra barcode printers is that the printer reports an error, and there will be various prompts on it, such as RIBBONOUT and PAPEROUT waiting on the panel.
The problem with this is that you cannot measure paper and ribbon failure. When this problem occurs, the first thing you want to do is to see if the label and ribbon are installed correctly. If it still doesn’t work after eliminating the above problems, then the Zebra barcode printer should perform advanced calibration on the label. If it still doesn’t work, you can restore the factory settings of the printer after knowing the printer parameter settings.
After the above method is used, the error is still reported, which is estimated to be a hardware problem. Please check whether there is dust on the label sensor and ribbon sensor, which can be cleaned with denatured alcohol. If this method still does not work, it is estimated that the main board of the barcode printer is broken.
2. The second common failure of the Zebra barcode printer is that the printer does not respond after printing, and there is no prompt on the printer screen. It is normal to feed the paper after pressing the paper button, which means that the printer does not report an error and the printer is good, and then the computer interface and data cable. If these two faults are excluded, the motherboard of the barcode printer will definitely be broken.
3. The third common failure of Zebra barcode printers is that the printer does not light up, the backlight of the screen is on, and the others do not respond. In our professional terminology, the main board does not light up. The only reason for the failure is that the chip on the main board of the printer is burned or short-circuited. The printer power board was working, so it was determined that the main board was bad.
4. The fourth common fault of Zebra barcode printers is that the printer does not light up, and the screen is completely black. The fault is that the power board is broken, and only one power board is shorted.
Matica Printer Film Search A1 Error
Matica XID8300 card printer reports Film Search A1 error
Matica XID8300 reports Film Search A1 error during use. This error means that there is a problem with the film tape used in the machine.
1. First open the cover of the machine to see if the film tape in the machine is used up. If it is used up, please replace it with a new film tape
2. Check whether the film belt in the machine is wrong, remove the film belt and refer to the installation diagram on the shelf, and reinstall the film belt again
3. If you have tried the above two methods and the fault persists, please contact our technical department in time!
Matica DIK10044 Cleaning Kit
Retransfers printer cleaning kit cleaning wipes industrial alcohol swabs.
EDI Secure DIK 10044 Retransfer Printer Cleaning Kit for EDI Secure XID and Secure IDX series, IDX3xx, DIS XID 430/440/450, XID 560/570/580/590ie, XID 8300, XID 9300/9330.
The EDI Secure DIK 10044 Cleaning Kit provides comprehensive cleaning and maintenance for your retransfer printer.
Printer Clean Swabs/Cleaning Stick for Card Printer/Thermal Printer
Printer clean swabs/cleaning stick for card printer/thermal printer
Specifications
1. cleaning help for large format printers.
2. cleaning swab stick/Cleaning wipes/non-woven cloth.
3. best price and fast delivery.
IPA isopropyl alcohol: As a chemical solvent in many industries, especially during electronics assembly and repair services.
The most typically made use of chemical solvent is isopropanol (IPA Swab).
It is very easy to liquify various polar and non-polar contaminants. Generally utilized to liquify and also remove light oil, finger prints, cutting liquid, flux deposits, carbon down payments and release representatives. It is also easily miscible with water, so it can additionally be used as a desiccant.
For applications on electronic printed circuit card (PCB) components, we use isopropyl alcohol to clean flux residues from PCB repair work and remodeling. Remove solder paste or sticky substances from SMT mesh. Our Maintenance with Isopropyl Alcohol cleans SMT reflow ovens, wave soldering jaws. Precision soldering tips, trays and any other flux buildup and carbonization that tends to collect during automated soldering.
Compatibility of isopropanol
Isopropyl alcohol swab is generally suitable with the majority of products utilized in digital products.
Printer Clean Swabs/Cleaning Stick for Card Printer/Thermal Printer
When solvents are incompatible with the substrate, they may cause cracking (microcracks), soften the material, or in the case of seals or gaskets, cause them to expand, shrink, or become brittle.
Quality or kind of isopropanol
There are several varieties and also grades of isopropanol, which are generally differentiated according to the amount of water in the remedy and other chemicals or non-volatile materials measured.
Isopropyl alcohol is hydrophilic or miscible with water, so it is simple to get water right into an azeotropic solution. When you see “70% isopropanol” on the tag, it describes the content of isopropanol related to dissolved water – that is, 70% isopropanol plus 30% water.
Water eliminated to create an extra pure isopropanol to develop the so-called “anhydrous” isopropanol.
IPA including 0.2% or 50% water has little impact on the look and smell of the material, however will considerably affect the surface area stress, or its moistening capability and also drying time. The more water containing isopropanol, the higher the surface area tension. This creates the solvent to come to be a lot more dry rather than wet or flaky, which might trigger areas. Cleaning up mirrors, lenses and also other optical tools “water areas” is specifically troublesome.
With the increase of the portion of water in the alcohol service, the drying time rises significantly. Depending upon the application, this can be a benefit or a drawback. For instance, isopropyl alcohol is frequently used as a flux eliminator to remove change residues around solder joints. Operators often tend to select fast drying, to ensure that they can clean up electronic equipment in time as well as recover it to use asap. In order to decay and eliminate thick, sticky or baked products that require even more time to remain or saturate, slowing down the drying out time normally improves the cleansing impact.
ACS/Reagent Grade – Satisfies or surpasses the pureness criteria established by the American Chemical Society (ACS). This quality applies to food, medication or pharmaceutical use and various other applications needing rigorous quality specifications as well as purity exceeding 95%.
USP Quality – Meets or surpasses the needs of the United States Pharmacopoeia (USP).
NF Quality – Satisfies or goes beyond the demands of the National Formulary (NF).
Lab Grade– The grade most commonly utilized for clinical applications, yet the exact impurity web content is unknown.
Purification quality – likewise referred to as “pure” or “useful quality”, which does not meet official requirements as well as is not enough for food, medication or clinical objectives.
The basic term “alcohol for external usage” typically describes isopropyl alcohol, but individuals who wish to acquire a specific quality of alcohol ought to prevent making use of items marked in this way. Outside alcohol does not refer to a certain grade, or perhaps various types of alcohol, such as ethanol
Customer alcohol for external usage may also have various other components, such as additives, seasonings and colorants, which are potential contaminants.
Cleaning up stick/dust-free cloth/non-woven towel for printer equipments.
ZEBRA ZC100 Card Printer Cleaning Pen / Cleaning Stick
ZEBRA (zebra) ZC100 card printer cleaning pen / cleaning stick
Why is it important to clean the printheads of card printers?
Because the printer head of the ZEBRA ZC100 card printer is a non-repairable accessory, if it is damaged, you can only replace the printer head. The printer head is permanently worn.
The operation steps to clean the printer head of the ZC100 card printer are very simple. You can use the cleaning pen and cleaning stick specially designed to clean the printer head. Note that you cannot use soaked cotton swabs instead of the cleaning stick. The main component of the cleaning pen and cleaning stick is absolute alcohol. , will not cause any damage to the print head, and the unique cleaning mixture will not leak or dry out.
The operation steps are as follows: the first step is to disconnect the power supply, the second step is to open the cover, and then gently wipe the print head several times with a cleaning pen to remove the accumulated dust on the print head. Touch the print head, clean the corners of the machine with a cleaning stick, and close the top cover of the printer after cleaning.
Generally, users only use the cleaning pen when they find that the printing effect is not good, such as white lines, unclear effect, ghosting, etc., but our technical suggestion is to wipe it once a week, which can reduce the loss of cards.
Both the cleaning pen and the cleaning stick can clean the printer head, but the cleaning stick can clean the tiny corners of the machine, and the two are used together.
Our company serves users wholeheartedly, professional technicians can solve the technical problems of the print head for you, and clean and maintain the printer with high-quality products for you . If you have any questions about card printers and printer consumables, please contact us.
